配资之家歡迎您的到来!

Banner
首頁 > 新聞 > 内容

新聞詳情

News detail

你不得不知的關于三維配资之家的日常保養維護的方法?

編輯:博牛宝沪深策略時間:2018-05-17

       三維配资之家和人一樣也是需要保養的,甚至它需要保養的程度遠遠超過人所需要的保養,好的保養可以大幅度的提高三維配资之家的壽命,從而大大提高经濟效益。那麼,三維配资之家日常該怎樣保養?三維配资之家出故障怎麼辦及配资之家故障分析?下面分析一下關于配资之家的日常保養和出現故障的解決辦法。

       Three-dimensional carving machine and people also need maintenance, it need maintenance is far more than one even need maintenance, good maintenance can greatly improve the life of a three-dimensional carving machine, thus greatly improve the economic benefit. So, how to maintain the 3d engraving machine? What is the fault of the 3d engraving machine and the fault analysis of the engraving machine? The following is an analysis of the daily maintenance of the engraving machine and the solution to the failure.

       三維配资之家系統屬數控系統一類,對電网環境有一定的要求,本系統所在的電网上應無電焊機,頻繁起动的機床,電动工具,無線電台等,強烈的電网幹擾導致電腦和三維配资之家系統的工作異常。

       Three-dimensional carving machine system belongs to the numerical control system, have certain requirements for grid environment, this system on the power grid should be no welding machine, frequent starting of machine tools, electric tools, radio stations, such as strong power grid disturbance caused computers and abnormal three-dimensional carving machine system work.

 一、保養是保證三維配资之家的使用壽命,提高設備效率的重要手段:

1、在實際使用中按照操作規範要求正常使用。

2、檢查連接主軸電機和水泵的水管,接通水泵電源,檢查水泵給排水工作是否正常。

3、为避免電源插座松动或接觸不良造成加工異常使産品報廢,請選擇良好的電源插座,應具有可靠的接地保護。

4、日常維護要求每天工作完成後進行工作台面和設備的清理加油以免造成不必要的損失。

5、定期維護要求每個月進行一次,維護的目的是檢查機器各個部位螺絲是否松动,确保機器潤滑條件和環境條件的良好。

1. Maintenance is an important means to ensure the service life of 3d engraving machine and improve the efficiency of equipment:
1. Normal use according to the operation specifications in actual use.
2. Check the main shaft motor and pump water pipe, connect the pump power supply, check whether the water pump water supply and drainage work is normal.
3. In order to avoid loose or poor contact of power socket, the product can be scrapped. Please choose a good power outlet, which should have reliable grounding protection.
4. Daily maintenance requires that the work table and equipment should be cleaned and refueling after daily work to avoid unnecessary losses.
5. Regular maintenance shall be conducted once a month. The purpose of maintenance is to check whether the screws of various parts of the machine are loose and to ensure good lubrication and environmental conditions.

三、故障分析報警故障:

超程報警,表示機器在運行過程中已达到極限为位置,請按以下幾個步驟檢查:  

所設計的圖形尺寸是否超出加工範圍。儀表顯示正常,電機不轉

(1)故障原因 ①閘把損壞判斷 ②調速轉把損壞判斷 ③電機損壞判斷 ④控制器損壞

(2)故障排除 ①拔下刹把插座(常开型刹把)。8~4。2V由低向高變化。電动开關車窗的耗電量很大,慢車狀态時激活的一刹那甚至會使引擎聲音發生變化,所以電池較弱的汽車,注意不要将車窗同時开或關。電动开關車窗动作不順暢的原因多为車門内部升降機里的油份耗盡,應取下内蓋加上油。若是玻璃完全不能动作,則有可能是开關故障。電子裝置如果不动作,檢查保險絲是一般常识。

3. Failure analysis and alarm failure:
The overpass alarm means that the machine has reached the limit in the running process. Please follow the following steps:
The size of the design is beyond the machining range. The meter shows normal and the motor does not turn.
(1) the failure causes the brake to turn the damage judgment on the damage judgment.
(2) troubleshooting and remove the brake socket (often open type brake handle). 8 ~ 4. 2V is changed from low to high. The electric power switch has a very high power consumption. In the moment of slow motion, the engine's voice will change, so the battery is weak, and the car should not be opened or closed at the same time. The reason for the unsmooth operation of the electric switch window is that the oil in the internal lift of the door is exhausted, and the inner lid should be removed and the oil is added. If glass is completely unable to move, it may be a switch fault. If the electronic device does not move, it is common knowledge to check the fuse.